manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 3

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

© June 2021 CommScope, Inc.

Page iii

T

ABLE

 

OF

 C

ONTENTS

Document Overview..................................................................................................................................................................................5

Document Revision History ..............................................................................................................................................................................7

Document Cautions and Notes......................................................................................................................................................................... 7

Abbreviations Used in this Guide .....................................................................................................................................................................8

CommScope Part Numbers ..............................................................................................................................................................................9

ERA System Overview.............................................................................................................................................................................. 10
WCS-2 and WCS-4 Subrack Overview....................................................................................................................................................... 11

WCS-2 and WCS-4 Subracks ...........................................................................................................................................................................11

WCS Subrack Back Panel Connectors.........................................................................................................................................................13

-48Vdc WCS Subrack Back Panel Connectors ............................................................................................................................................14

WCS Subrack Alarm Connector..................................................................................................................................................................15

WCS Subrack Slot and Card Assignments ..................................................................................................................................................17

Slot and Card Assignment Rules for Classic CANs ............................................................................................................................................. 18

Slot and Card Assignment Rules for Switching CANs ........................................................................................................................................ 19

Slot and Card Assignment Rules for WINs ........................................................................................................................................................ 20

Slot and Card Assignment Rules for TENs ......................................................................................................................................................... 21

WCS Subrack Cards.........................................................................................................................................................................................22

System User Interface (SUI) Card...............................................................................................................................................................22

RF Donor (RFD) Card and RF Donor (RFD) HB Card....................................................................................................................................23

Optical Transport (OPT) Card.....................................................................................................................................................................26

Copper Transport (CAT) Card.....................................................................................................................................................................27

Auxiliary Unit Transport (AUT) Card ..........................................................................................................................................................28

CPRI Digital Donor Card .............................................................................................................................................................................29

CDD Card CPRI Ports ......................................................................................................................................................................................... 29

CDD Card CPRI Port LEDs................................................................................................................................................................................... 30

WCS Subrack Fan Trays and Filter Modules ...................................................................................................................................................31

Cat6A Cables and Connectors.........................................................................................................................................................................32

Power Supply Unit Subrack and Rectifier Modules................................................................................................................................... 33

Power Supply Unit Subrack.............................................................................................................................................................................33

12 Vdc Rectifier Module .................................................................................................................................................................................35

57 Vdc Power Rectifier Module......................................................................................................................................................................36

57 Vdc Power Rectifier LEDS......................................................................................................................................................................36

Maximum Number of APs that can be Powered by WCS Subrack .................................................................................................................37

ERA Software Power Estimates..................................................................................................................................................................37

CAT Cards...................................................................................................................................................................................................37

WCS Subracks, 57 Vdc Rectifier Modules, and Service Voltage.................................................................................................................38

APs in a Mixed Copper CAP L and UAP System..........................................................................................................................................39

Optional e-POI Subracks .......................................................................................................................................................................... 40

Interface Card (IFC).........................................................................................................................................................................................41

e-POI Modules ................................................................................................................................................................................................42

Safely Working with ERA Hardware ......................................................................................................................................................... 43

Health and Safety Precautions ....................................................................................................................................................................... 43

Property Damage Warnings ...........................................................................................................................................................................43

General Installation Safety Requirements......................................................................................................................................................44

Guard Against Damage from Electro-Static Discharge ...................................................................................................................................44

Compliance.....................................................................................................................................................................................................44

Equipment Symbols Used / Compliance.........................................................................................................................................................47

Install the Subracks and PSU in an Equipment Rack ................................................................................................................................. 48

WCS Subrack Type Considerations .................................................................................................................................................................48

Unpack and Inspect the Subracks and Components ......................................................................................................................................48

Rack-Mount the Subracks and PSU (WCS-2, WCS-4)......................................................................................................................................49

Connect the WCS Rear-panel Cables..............................................................................................................................................................51

Rack-Mount the Subracks (-48Vdc WCS-2, WCS-4)........................................................................................................................................53

Connect the -48Vdc WCS Rear-panel Cables..................................................................................................................................................54

Install and Connect the Subrack Cards ..................................................................................................................................................... 56

Install a Subrack Card .....................................................................................................................................................................................56

Connect the SUI Card......................................................................................................................................................................................57

Connect the RFD Cards ...................................................................................................................................................................................58

Connect the OPT Cards...................................................................................................................................................................................60

Fiber Optic Link Budget in the ERA System................................................................................................................................................60

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands