manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 30

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

M0201ABK_uc 

Page 30

© June 2021 CommScope, Inc.

 WCS-2 and WCS-4 Subrack Overview

 

CDD Card CPRI Port LEDs

A CDD Card has six LEDs that correspond to its six CPRI ports, as shown in the following graphic and table.

LED Color

Affected LEDs

State

Off

All six

No power to the CDD Card. If this state is not expected, do the following in the order presented:
1 Verify that the CAN is powered on (the CAN powers the CDD).
2 Verify that the CDD Card is enabled; the default setting is 

Off

 (disabled) and must be manually set to 

On

 (enabled). 

3 Reseat the CDD Card in its slot or move it to another slot to make sure there is firm connectivity with 

the WCS Subrack.

Flashing Red

All six

Can be any of the following:
• External Power Supply Failure—board power failure.
• There is a boot error.

CPRI port specific • CPRI port is not communicating with the WCS/CAN.

Solid Red

All six

Can be any of the following:
• CDD Card is receiving power, but its FPGA has not loaded.
• CDD Card is in Bootloader mode and its RAM test failed.

CPRI port specific • An SFP Module is not present in the CPRI port, but the CDD Card is configured via the ERA software. 

Verify that there is an SFP Module installed and is firmly seated in the CPRI port.

Flashing Amber All six

Firmware download is in process. Note that this process includes matching the CDD Card firmware to 

the ERA Software Version running on the CAN in which the CDD Card is being installed. If the firmware 

on the CDD Card is different from the CAN, it will take slightly longer to download the firmware to the 

CDD Card. Wait until the LEDs are solid amber before configuring the CDD Card.

Solid Amber

All six

Can be any of the following:
• All firmware updates have been pushed to each port and the CDD Card is ready to be configured.
• The port has been configured from the DAS side, but the BBU has not provided a carrier yet.

Flashing Green CPRI port specific The BBU has provided a carrier, but the Signal Set has not yet been created and linked to an AP.
Solid Green

CPRI port specific Port is configured for a Carrier and the Signal Set is being distributed to an AP.

Six CPRI Port LEDs

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands