manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 15

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide 

© June 2021 CommScope, Inc.

Page 15

WCS-2 and WCS-4 Subrack Overview

WCS Subrack Alarm Connector

External alarms are connected to the WCS using a connector inserted into the alarms port located on the rear 

of the WCS. 
The alarm connector on the WCS-4 and WCS-2 Subracks has the following inputs: 

•

four opto-isolated (chassis-ground referenced) dry contact inputs to monitor external devices. The alarm 

state is activated when the alarm input is pulled to ground. The alarm input is referenced to chassis 

ground, and the alarm ground is tied to the chassis ground. 

•

a Summary Alarm Relay that energizes when specific alarms are triggered-the thresholds, shown in the 

following graphic. The Summary Alarm state changes whenever there is an alarm on the system and 

returns to its default state when there are no alarms. Depending on which contacts you use the default 

state is either Normally Closed or Normally Open. 

The alarm connector on the WCS-4 and WCS-2 Subracks has the following output:

•

The external alarm output is activated at the CAN whenever there is a critical or major alarm in the 

system. The alarm output is provided by a relay. Both normally open and normally closed terminals are 

available.

The following table shows the alarm connector details for the system parameters.

The following table shows the alarm connector details for the connectable conductors. 

Included in the box, the mating connector for the Alarm connector (header) is Weidmuller part 

1748040000. 

NC

COM

NO

ALARMS

1

2

3

4

5

6

Relay COM

GND

IN 1

IN 2

IN 3

IN 4

Relay  NO

Relay NC

Summary Alarm

0.8 A max

30 Vdc max

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands