manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 56

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

M0201ABK_uc 

Page 56

© June 2021 CommScope, Inc.

 Install and Connect the Subrack Cards

 

I

NSTALL

 

AND

 C

ONNECT

 

THE

 S

UBRACK

 C

ARDS

The following sections tell you how to install a card into a WCS Subrack, add SPF+ transceivers to an OPT 

Card, and how to connect the Subrack cards to the ERA system. 

Install a Subrack Card

Do the following to install an ERA card into a WCS-2 or WCS-4 Subrack. 

1

Observe all cautions in 

"Safely Working with ERA Hardware” on page 43

.

2

Follow the rules listed in 

"WCS Subrack Slot and Card Assignments” on page 17

 to identify in which slot(s) 

a card to install in a WCS-2 or WCS-4 Subrack to configure the Subrack as a Classic CAN, Switching CAN, 

WIN, or TEN.

3

CDD Cards and RFD Cards should be populated in the Subrack from bottom to top starting with the 

bottom slot of each section of the Subrack (Slot R1 or Slot R5) to ensure optimal cooling of the cards. For 

example, if you have only one CDD Card, it should be installed in Slot R1 and blank panels should be 

installed in R2-R4.

4

Remove the blank panel from the slot in which a card is to be installed.

a

Loosen the silver PEM screw on the left that secures the blank panel to the Subrack. 

b

Reserve the blank panel for future use.

5

Install the card in the Subrack.

a

Use the black Support knob on the right of the card’s faceplate to slide the card into its slot, and then 

push the card into its slot back until the card’s faceplate is flush against the Subrack chassis.

b

Tighten the silver PEM screw on the left of the card’s faceplate to secure the card to the Subrack 

chassis.
The following graphic shows the PEM screw and support knob on a CDD Card. Although other cards 

will have different connectors and LEDs, the positioning of the PEM screw and Support knob will be 

the same.

c

Do not leave any unoccupied slots open; replace blank panels, as necessary

When installing a Card into or removing it from a Subrack, keep the Card level. Tipping the Card up or 

down during installation or extraction may cause it to strike another component in the Subrack, which 

can damage the Card and/or the component that was struck.

PEM

screw

Support

knob

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands