manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 57

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide 

© June 2021 CommScope, Inc.

Page 57

Install and Connect the Subrack Cards

.

Connect the SUI Card

The SUI Card allows you to connect the WCS Subrack to a local laptop, LAN, or modem. Connect any of these 

devices as required for local practice. 

•

Local:

 Use Ethernet CAT 5 cable (straight or crossover) with RJ-45 connectors to connect a local laptop 

or PC to the Local port to allow for administration of the ERA system through the ERA software. 

•

LAN2:

 Use Ethernet CAT 5 cable (straight or crossover) with RJ-45 connectors to connect your LAN or a 

modem to the LAN2 port.

To maximize airflow through the WCS and e-POI chassis, blank panels must be installed in all empty slots. 

If additional blank panels are required, contact your local CommScope sales representative to order the 

appropriate panel:
• ERA Blank Panel Universal (PN 7688866-xx)
• ERA Blank Panel SUI (PN 7688868-xx)
• ERA Blank Panel AUT (PN 7688867-xx).

CDD Cards and RFD Cards should be populated in the Subrack from bottom to top starting with the 

bottom slot of each section of the Subrack (Slot R1 or Slot R5) to ensure optimal airflow to the cards.

The LAN1 port is not currently used.
The USB port is reserved for use by CommScope. 

SUI Cards are hot swappable; you do not need to power down the CAN, TEN, or WIN to install or remove 

an SUI Card.

USB

port

Local

port

LAN1

port

LAN2

port

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands