manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 7

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide 

© June 2021 CommScope, Inc.

Page 7

Document Overview

Document Revision History

This is the tenth release of the 

WCS-2, WCS-4, and e-POI Subracks and Power Supply Unit Installation Guide

, 

CommScope Document Number M0201ABK. This release of the manual 

•

corrects the Summary Alarm voltage and current maximum values previously listed in the guide for the 

Alarm Connector. The correct maximum values supported are 0.8 A and 30 Vdc. The 125 Vac value 

previously listed is not supported. Also the image of the alarm connector was replaced to show the actual 

connector shipped with the unit; see 

"WCS Subrack Alarm Connector” on page 15

.

•

adds the minimum ERA software versions required to support new RFD Card PN 7633229-03, which has 

been updated with new subcomponents to prevent material delays or obsolescence.

•

adds the minimum ERA software versions required to support new RFD Card PN 7633229-05 for APs that 

support TETRA services; see 

"RF Donor (RFD) Card and RF Donor (RFD) HB Card” on page 23

.

•

added the maximum wire size and minimum recommended wire size for the -48Vdc WCS subrack’s DC 

power entry connector; see

"Connect the -48Vdc WCS Rear-panel Cables” on page 54

.

•

removed note referring to a discontinued CDD Card configuration guide because the CDD information is 

contained in this guide.

Document Cautions and Notes

This document may contain any of the following notes, cautions, and warning icons. 

The icon to the left is used to indicate a caution or warning. Cautions and warnings indicate operations or 

steps that could cause personal injury, induce a safety problem in a managed device, destroy or corrupt 

information, or interrupt or stop services.

The icon to the left indicates a caution or warning that pertains to laser equipment.

The icon to the left indicates a caution or warning that pertains to Radio Frequency (RF).

The icon to the left indicates that the hardware is susceptible to Electro-Static Discharge (ESD) damage.

The icon to the left indicates a caution or warning that pertains to an electrical hazard.

The icon to the left indicates a caution or warning that pertains to a fire hazard.

The icon to the left indicates a Note. Notes provide information about special circumstances.

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands