manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 52

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

M0201ABK_uc 

Page 52

© June 2021 CommScope, Inc.

 Install the Subracks and PSU in an Equipment Rack

 

2

Connect the DC Power cable and the Rectifier Control cables that shipped with the PSU shelf assembly.

a

Do the following before connecting the WCS PSU Cable or the Rectifier Control Cable:

•

Confirm that all AC power cables are unplugged from the rear of the PSU. 

•

Remove 12 Vdc Rectifier Modules and 57 Vdc Rectifier Modules from the PSU. Do not skip this 

step. Residual charge is still available in the Power Modules for a short period after AC input is lost 

and connecting the WCS PSU Cable or the Rectifier Control Cable with 

any

 power in the PSU can 

damage the WCS.

b

Plug the DC Power Cable, which is attached to the rear of the PSU, into the WCS Subrack power 

connector, and then use a flat-blade screwdriver to tighten the two mounting screws.

c

Slide the Power Connector shell over the Subrack power connector and tighten the two thumbscrews 

to attach it to the WCS Subrack.

d

Plug the Rectifier Control Cable (shown to 

the right) into the WCS Rectifier Control 

connector; press it in until you hear it click 

and lock into place.

e

Plug the other end of the Rectifier Control Cable to the matching connector (unlabeled) on the rear of 

the PSU.

3

Connect the Ground stud on the WCS, PSU, and e-POI Subracks to a suitable earth ground, per local and 

national electrical codes.

4

Reseat the 12 Vdc Rectifier Modules and 57 Vdc Rectifier Modules in the PSU.

5

Plug AC power cables into the power connectors on the rear of the PSU. 

To prevent damage to the WCS, tighten the two DC Power Cable mounting screws to ensure that the DC 

Power Cable cannot be accidentally dislodged.

WCS PSU Cable

Recfier Control Cable

To prevent SEVERE damage to the WCS Subrack, confirm that all AC power cables 
are unplugged from the rear of the PSU BEFORE plugging/unplugging the 
WCS Power or Recfier Control cables into/from the WCS subrack.

CAUTION!

Rear Panel of PSU

+57 Vdc Power terminal
- 57 Vdc Power terminal

Recfier Control connector

+12 Vdc Power terminal
- 12 Vdc Power terminal

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands