manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 41

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide 

© June 2021 CommScope, Inc.

Page 41

Optional e-POI Subracks

Interface Card (IFC)

The IFC (PN 7676260-xx) is used to set the Subrack number of the e-POI Subrack. It also provides 

communications, status, and alarms for the e-POI Modules installed in the e-POI Subrack.
The following graphic and table identify the IFC Card LEDs and connectors. 

IFC LEDs

Ref # LED

LED Color

Description

1

Status 

• Off

• The e-POI Subrack or the IFC is not 

fully seated or is not receiving 

power.

• Green

• e-POI Subrack or IFC is functioning to 

specification.

• Red

• Active alarm on e-POI Subrack or IFC.

4

e-POI Module

Status 1 - 8

• Off

• e-POI Module in corresponding slot 

is not receiving power.

• Green

• e-POI Module in corresponding slot 

is functioning to specification. e-POI 

Module Status LED must be green 

before connecting corresponding RF 

signals to input.

NOTE:

If e-POI Module is not 

functioning, PIM or VSWR 

rating could be 

compromised, causing an 

alarm on the BTS.

• Red

• e-POI Module in corresponding slot 

has active temperature alarm.

IFC Connectors

Ref # Component

Device

Function

2

Address switch

Rotary dial Must be set to 

1

.

3

Config button

Pushbutton Alerts ERA Software to scan for and 

remove references to removed RFD 

Cards; see 

"Removing an e-POI Module 

from an e-POI Subrack” on page 80

.

1

2

3

4

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands