manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 22

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

M0201ABK_uc 

Page 22

© June 2021 CommScope, Inc.

 WCS-2 and WCS-4 Subrack Overview

 

WCS Subrack Cards

The following sections describe the cards that can be installed in a WCS Subrack.

•

"System User Interface (SUI) Card” on page 22

•

"RF Donor (RFD) Card and RF Donor (RFD) HB Card” on page 23

•

"Optical Transport (OPT) Card” on page 26

•

"Copper Transport (CAT) Card” on page 27

•

"Auxiliary Unit Transport (AUT) Card” on page 28

•

"CPRI Digital Donor Card” on page 29

.

System User Interface (SUI) Card 

The SUI Card (PN 7642125-xx) provides local and LAN Ethernet connections and a USB port. You install only 

one SUI Card in a Subrack, and it must always be installed in Slot M3. 
The following graphic and table identify the SUI Card LEDs and connectors. 

SIU Card LEDs

Ref # LED

LED Color

Description

1

Right 

• Off

• No link.

• Green

• Link established with device to which the port is connected.

• Flashing green • Activity is occurring on that port.

Left

• Off

• 10 Mb connection established.

• Yellow

• 100 Mb connection established.

SIU Card Connectors

Ref # Component Device

Function

2

USB port

2.0 USB

Reserved for use by CommScope.

3

Local port

RJ-45 jack (female) Connects to a local laptop; DHCP or specified fixed IP address.

4

LAN1 port

RJ-45 jack (female) Reserved for future use.

5

LAN2 port

RJ-45 jack (female) Connects to a LAN or modem; DHCP or specified fixed IP address.

2

3

4

5

1

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands