ComAp InteliNano NT Plus Reference Manual Download

Page: 2 / 90

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

Normally Closed Contact ..................................................................................................... 34

7.2

Outputs settings ............................................................................................................................. 35

Binary outputs InteliNano

Plus - default ............................................................................ 35

8.1

Logical binary outputs .......................................................................................................... 35

8.2

Inputs settings ................................................................................................................................ 44

Binary and analog inputs InteliNano

Plus - default ........................................................... 44

9.1

Logical binary and analog inputs ......................................................................................... 44

9.2

Setpoints ................................................................................................................................... 58

B - Basic settings ................................................................................................................. 61

10.1

E - Engine parameters and protections ............................................................................... 67

10.2

G - Generator protections .................................................................................................... 71

10.3

– AMF (Auto Mains Failure) settings ................................................................................ 73

10.4

ECU .......................................................................................................................................... 75

CAN bus wiring .................................................................................................................... 75

11.1

Alarms, Events and History Management ................................................................................ 76

Events .................................................................................................................................. 78

12.1

Warnings .............................................................................................................................. 80

12.2

Shutdowns............................................................................................................................ 82

12.3

ECU Messages .................................................................................................................... 86

12.4

Technical data .......................................................................................................................... 87

Power supply ........................................................................................................................ 87

13.1

Operating conditions ............................................................................................................ 87

13.2

Physical dimensions ............................................................................................................. 88

13.3

Binary inputs ........................................................................................................................ 88

13.4

Binary outputs ...................................................................................................................... 88

13.5

Analog inputs ....................................................................................................................... 89

13.6

Generator/Mains measurements ......................................................................................... 89

13.7

Charging alternator preexcitation circuit .............................................................................. 89

13.8

Communication interface ..................................................................................................... 89

13.9

CAN interface ....................................................................................................................... 89

13.10

Summary of Contents for InteliNano NT Plus



























































































Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands

ComAp InteliNano NT Plus, Reference Manual

Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands