ComAp InteliNano NT Plus Reference Manual Download

Page: 78 / 90

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

Events

12.1

Every event listed in table below is saved in history with running hours stamp see

Figure 12.3

EVENT

–

OWER

Possible Events

Mains Return

Mains has returned. All mains parameters are within the preset range.

Mains Fail

Mains failure detection depends on Auto mains failure setpoints.

Manual Start

Engine was manually started by pressing button

Start

Manual

mode.

Remote Start

Engine was remotely

started via input terminal’s function

I02 Remote Start/Stop

I03 Remote Start And Load

. The controller is in

Auto

mode.

AMF Start

Engine was automatically started because of mains failure. The controller is in

Auto

mode.

Manual Stop

Engine was manually stopped by pressing button

Stop

Manual

mode.

Remote Stop

Engine was remotely

stopped via input terminal’s function

I02 Remote Start/Stop

I03 Remote Start And Load

. The controller is in

Auto

mode.

Summary of Contents for InteliNano NT Plus



























































































Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands

ComAp InteliNano NT Plus, Reference Manual

Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands