ComAp InteliNano NT Plus Reference Manual Download | Manualshive

Page: 47 / 90

background image

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

47

I00

Not Used

Input has no function. Use this configuration when binary or analog input is not connected.

Hint:

T07 T07

is input-output terminal. Primarily it is configured as an output. To configure as an input,

assign the function

O00 Not Used

in the output configuration.

I01

Emergency Stop

This input will activate the built-in

Emergency Stop

alarm. It is recommended to use a

button for this input.

If this binary input is activated, the left red LED above

Stop

button will blink, the general shutdown

symbol will be dis

played on LCD’s upper right corner,

Emergency Stop

symbol will be displayed on

event log with running hours stamp and shut down procedure will occur. For more details see
Shutdown procedure in chapter

12 Alarm, Events and History Management.

C

AUTION

!

This is a software function only.

I02

Remote Start/Stop

9.2.1

This input is an external request for engine run. It is active in

Auto

mode only.

In MRS mode the controller starts the engine and keeps GCB open.
In AMF mode the controller starts the engine and keeps GCB open. Only when mains fail occur GCB
is automatically closed.

N

OTE

:

The

Remote Start/stop

can be configured only on terminal

This is also used for waking the

controller from “Zero Power” mode.

I03

Remote Start And Load

9.2.2

The

Remote Start And Load

input can be used only when the controller is in

Auto

mode.

In AMF mode this input starts the engine and transfers the load to the generator after all engine and
generator parameters are within tolerance (open MCB and close GCB). When this input is
deactivated the controller will transfer the load back to mains and stop the engine.

In MRS mode this input starts engine and closes the GCB (only when is configured). When this input
is deactivated the controller will open the breaker (only when is configured) and stop the engine.

N

OTE

:

The

Remote Start And Load

can be configured only on terminal

. This is also used for waking

the controller from “Zero Power” mode.

«
...
45
46
47
48
49
...
»

Summary of Contents for InteliNano NT Plus



























































































Reviews:

No comments

Related manuals for InteliNano NT Plus

ClubSport Wheel Base V2

Brand: FANATEC Pages: 39

Brand: UniKey Pages: 20

Brand: IBM Pages: 12

Brand: K&K Pages: 10

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 8

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 2

ECL Comfort 110

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands