ComAp InteliNano NT Plus Reference Manual Download

Page: 84 / 90

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

External Shutdown 3

GCB Fail

Failure of generator circuit breaker.

Generator Overvoltage

Generator will stop when output voltage exceeds the preset threshold

G01 Generator

Overvoltage Shutdown.

Generator Undervoltage

Generator will stop when output voltage drops below the preset threshold

G02

Generator Undervoltage Shutdown.

Generator Overfrequency

The generator frequency is out of limits given by setpoints

G03

Generator

Overfrequency Shutdown

and

G04

Generator Underfrequency Shutdown

Generator Underfrequency

The generator frequency is out of limits given by setpoints

G03

Generator

Overfrequency Shutdown

and

G04

Generator Underfrequency Shutdown

Generator CCW Rotation

Incorrect generator phase sequence.

Start Fail

Gen-set start failed.

Stop Fail

Gen-set stop failed.

Battery Flat

If the controller loses power during starting sequence due to bad battery condition, it
will not try to start again and will activate this protection.

Summary of Contents for InteliNano NT Plus



























































































Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands

ComAp InteliNano NT Plus, Reference Manual

Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands