ComAp InteliNano NT Plus Reference Manual Download | Manualshive

Page: 48 / 90

background image

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

48

I04

Access Lock

9.2.3

When this input is closed, no setpoints can be adjusted from controller’s front panel and gen-set
mode (

Manual

-

Auto

) cannot be changed.

Access Lock

does not protect setpoints and mode changing from

NanoEdit

. Also history is

accessible.

Access Lock

is also functionless in case that the controller is in setup mode.

I05

AMF Blocked

When this input is closed, the automatic start of the gen-set at Mains failure is blocked. If the gen-set
is running, the GCB is opened, and gen-

set stops. This input doesn’t affect the mains circuit breaker.

I06

MCB Feedback

This input indicates whether MCB is closed or opened. Available only in AMF mode.

I07

GCB Feedback

This is an input from the generator circuit breaker. If the input is active, the controller will consider the
GCB as closed and vice versa. If the GCB is not in expected position, the alarm

will occur.

For more details see

procedure in chapter

12 Alarm, Events and History Management.

N

OTE

:

The feedback time limit is 5s.

GCB position is indicated on the mains screen when feedback is configured.
Wrong breaker / contactor position is indicated on mains screen also.

GCB is opened but has to be close.

GCB is closed but has to be open

I10

External Warning 1

If this binary input is activated the red LED above

Stop

button will blink, general warning symbol will

be displayed on LCD’s upper right corner and

External Warning 1

symbol will be displayed on event

log with running hours stamp. This alarm is only warning. For more details see

procedure in

chapter

12 Alarm, Events and History Management.

«
...
46
47
48
49
50
...
»

Summary of Contents for InteliNano NT Plus



























































































Reviews:

No comments

Related manuals for InteliNano NT Plus

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: Gardena Pages: 17

Brand: SAFI Pages: 18

Brand: Badger Meter Pages: 2

Brand: Badger Meter Pages: 48

BadgerTouch HREBT

Brand: Badger Meter Pages: 12

Brand: Badger Meter Pages: 16

Brand: FATEK Pages: 10

Brand: Gatekeeper Pages: 28

Brand: Quinny Pages: 21

Brand: GBD Pages: 60

Brand: Carel Pages: 48

Brand: ESBE Pages: 4

Controller CR100

Brand: Sonos Pages: 12

Brand: AC Tech Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands