ComAp InteliNano NT Plus Reference Manual Download | Manualshive

Page: 4 / 90

background image

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

4

N

OTE

:

ComAp believes that all information provided herein is correct and reliable and reserves the right to
update at any time. ComAp does not assume any responsibility for its use unless otherwise expressly
undertaken.

N

OTE

:

SW and HW must be compatible otherwise some functions will be disabled.

N

OTE

:

Because of large variety of the

InteliNano

NT

parameters settings, it is not possible to describe all

combinations. Some of the

InteliNano

NT

’s functions are subject of changes depend on SW version.

The data in this manual only describes the product and is not intended as a warranty of performance
or characteristics.

C

AUTION

!

Dangerous voltage

In no case touch the terminals for voltage measurement!

Always connect grounding terminals!

C

AUTION

!

All parameters are preset to initial values. But the set points in the “

Basic settings

” settings group

!!must!!

be adjusted before the first startup of the gen-set.

!!! INCORRECT ADJUSTMENT OF BASIC PARAMETERS

CAN RESULT IN DAMAGE TO THE GEN-SET !!!

The following instructions are for qualified personnel only. To avoid personal injury do not perform any

action not specified in this User guide!!!

W

ARNING

!

Every time the following

InteliNano

NT

controller terminals are disconnected:

▪

Mains voltage measuring and / or

▪

Binary output for MCB control and / or

▪

MCB Feedback

Disconnect power supply from the

InteliNano

NT

controller and/ or disconnect the binary outputs

and Fuel to avoid unexpected automatic start of gen-set and GCB closing!

W

ARNING

!

Remote control

The

InteliNano

NT

controller can be controlled remotely. When working on the gen-set, ensure that

remote start is disabled.

This is done by:

Disconnect input REM START/STOP

or

Disconnect output

and outputs

GCB Close/Open

and

MCB Close/Open

«
...
2
3
4
5
6
...
»

Summary of Contents for InteliNano NT Plus



























































































Reviews:

No comments

Related manuals for InteliNano NT Plus

Brand: Vacon Pages: 64

Smart-MPPT Li Series

Brand: Y-Solar Pages: 6

Brand: Ickle Bubba Pages: 23

Brand: Yardney Pages: 8

Brand: Campbell Pages: 8

Brand: Campbell Pages: 22

Brand: Samson Pages: 52

Brand: Vaillant Pages: 32

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 40

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Eaton Pages: 10

Brand: Idemia Pages: 29

Brand: Dantherm Pages: 20

Brand: DigiPower Pages: 27

Brand: M-system Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands