ComAp InteliNano NT Plus Reference Manual Download

Page: 37 / 90

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

O00 Not Used

Output has no function. Use this configuration when output is not connected.

O01 Starter

This output is dedicated for starter motor control. The number of cranking attempts is 6.

Prestart Time

0 - 600 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Cranging Fail

Pause 8 s

Gen-set start failed

Off

Start

Starter Output

Time

6 Cranking Attempts

Prestart Time

Maximum

Cranking Time

0 - 60 s

Gen-set start failed – shutdown,

if the voltage or frequency are not in

the limit

Off

Time

Start

Engine run

Max. Stab. Time 7 s

Min. Stab. Time

Starter Output

The starter output become inactive when one of following conditions is reach or exceeded.

RPM

≥ 25% of nominal RPM (1500RPM=50Hz; 1800RPM=60Hz)

Oil Pressure Analog

≥ 3 bar (43 PSI), only when

Oil Pressure Starter Disengagement

is enabled

Low Oil Pressure

input is opened, only when

Oil Pressure Starter Disengagement

is enabled

or
voltage on D+ terminal ≥ 80% of battery voltage for 1 s or longer

Summary of Contents for InteliNano NT Plus



























































































Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands

ComAp InteliNano NT Plus, Reference Manual

Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands