ComAp InteliNano NT Plus Reference Manual Download | Manualshive

Page: 83 / 90

background image

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

83

12.3.5

Inactive confirmed shutdown

O04 Alarm

output is opened. It is possible to start engine when all shutdowns are inactive and

confirmed.

Figure 12.9

INACTIVE CONFIRMED SHUTDOWN

–

E

MERGENCY

S

TOP

12.3.6

Possible shutdown alarms

Emergency Stop

The binary input

Emergency Stop

was activated.

Overspeed

The protection comes active if the speed is greater than 115% of nominal engine
RPM, which is derived from generator frequency.

Underspeed

Low engine RPM. This alarm will be issued when the gen-set is running and then
stops by itself, i.e. the RPM drops under the nominal engine RPM.
The underspeed alarm starts to be evaluated 5 sec after successful gen-set start and
is being evaluated all the time the

Fuel Solenoid

is on.

Low Oil Pressure

Engine will stop when oil pressure declined to or less than 1 bar or binary input

Low Oil Pressure

is active.

High Coolant temperature

Engine will stop when temperature of coolant exceed

Coolant Temperature Shutdown

threshold.

External Shutdown 1

External Shutdown 2

«
...
81
82
83
84
85
...
»

Summary of Contents for InteliNano NT Plus



























































































Reviews:

No comments

Related manuals for InteliNano NT Plus

Brand: Taie Pages: 66

Brand: Mamas & Papas Pages: 16

Brand: Badger Basket Pages: 3

Brand: BADLANDS Pages: 2

Brand: Calsense Pages: 74

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brand: Parker Pages: 21

Brand: Parker Pages: 26

Brand: Parallax Pages: 3

Brand: Vageo Pages: 2

Brand: Yealink Pages: 8

Brand: C&C Pages: 17

Brand: Vizio Pages: 65

Brand: I-Tork Pages: 15

Brand: MGC Pages: 16

Brand: IBM Pages: 214

Brand: STIEBEL ELTRON Pages: 44

Brand: micro-trak Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands