ComAp InteliNano NT Plus Reference Manual Download

Page: 38 / 90

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

O02 Fuel Solenoid

This output is dedicated to control the fuel solenoid (valve). The output is closed in the same time as

Starter

output and remains closed while the engine is running.

Prestart Time

0 - 600 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Cranging Fail

Pause 8 s

Cranging Fail

Pause 8 s

Gen-set start failed

Starter Output

Off

Fuel Solenoid is
opened

Start

Time

Prestart Time

Maximum

Cranking Time

0 - 60 s

Off

Time

Start

Engine run

Max. Stab. Time 7 s

Min. Stab. Time

Starter Output

Stop

Fuel Solenoid is
opened

Summary of Contents for InteliNano NT Plus



























































































Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands

ComAp InteliNano NT Plus, Reference Manual

Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands