ClearSpan Gro-Max 108179H Manual Download

Page: 32 / 53

Revision date: 09.18.14

CLEARSPAN

™

GRO-MAX GOTHIC HIGH TUNNELS

TWIST-OF-THE-WRIST ASSEMBLY

Gather the parts:
• Aluminum channel (102570) and drive handle

(102480)

• Gearbox (103496) and gearbox drive (102717)
• Mounting plate (103544), bearing (102569), and

threaded rod (FAK26)

• 3/8" nuts (FALB04B) and 3/8" washers (FAME08B)

The Twist-of-the-Wrist Assembly is designed to roll up the

side curtain. The following steps describe the assembly

and its installation.

1. Measure 1/2" in from the end of the roll-up conduit,

center-punch the location on the pipe, and drill a 5/16"

hole through the conduit.

1/2"

2. Insert a tubing

adapter into the

conduit and align

the holes of the

adapter with the

drilled holes in

the conduit.

4. Position the channel along the end rafter where the

Twist-of-the-Wrist assembly will be located.

5. Secure the upper end of the channel by drilling a 3/8"

hole through the end rafter and attach as shown.

The lower end of the channel will "float" and is not

attached.

Photo shows a different model and is used for illustration

purposes only. Use an FAME08B washer to protect end

panel if equipped.

3. Select the aluminum channel, drill a 3/8" hole through

the channel approximately 2" from the end, and attach

a threaded rod using a 3/8" nut on each side of the

102570 channel.

Do not allow channel to contact the ground. Use the

position of the roll-up conduit, which is at the base of

the frame along the side, to help align the channel

when securing it in place.

Top View

End

Rafter

Threaded

Rod

(FAK26)

FAME08B

Washer

FALB04B

Washer

End Rafter

Threaded

Rod

(FAK26)

Double

U-Channel

Ground Post

or Rafter Leg

Guide

Channel

(102570)

Gear Box

(103496)

FAH005B

Bolt

Roll-Up Side

Conduit

Baseboard

Trim conduit to

meet gearbox.

Adjust threaded

rod as needed.

Summary of Contents for Gro-Max 108179H






















































Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands

ClearSpan Gro-Max 108179H, Manual

Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands