manualshive.com logo in svg

ClearSpan Gro-Max 108179H, Manual

Share
Download
ClearSpan Gro-Max 108179H Manual Download Page 5

5

Revision date: 09.18.14

CLEARSPAN

™

 GRO-MAX GOTHIC HIGH TUNNELS

Ground 

Level

Inside of 

Shelter

Outside of 

Shelter

BASEBOARD NOTE

A customer-supplied baseboard and retaining board 

are required

 to attach the drop-down side curtains. The 

baseboard is optional but recommended for a building 

with a roll-up side. See the exploded view below. 

The baseboard runs the length of the frame at ground 

level. The retaining board secures the drop-down curtain 

to the baseboard. 

The baseboard and retaining board are 

supplied by the customer.  

 

Retaining boards are attached during the drop-down 

curtain installation. The retaining board is not used when 

the building is equipped with a roll-up curtain. 

Ground Level

Drop-Down 

Curtain

Optional 

End Panel

Retaining Board

Baseboard

View shown from outside the shelter.

Fasteners (1/4" x 4" carriage bolts (FAH009B) and FA4652 

wood screws) are included. Depending on board width, use 

2 carriage bolts per rafter connection for the baseboard 

and ribbon board. Evenly space the wood screws at 24". 

Countersink heads if needed.

ATTENTION:

 A baseboard is not required for buildings with 

a roll-up side curtain, but installing a baseboard is strongly 

recommended. Fasteners are included to attach the boards 

to the frame. Customer supplies baseboard material.

Secure baseboard and ribbon 

board joints between rafters 

as shown for best results.

RIBBON BOARD REQUIRED: DROP-DOWN SIDES

A customer-supplied two-piece ribbon board is required 

for the installation of the drop-down curtain. Fasteners are 

included. 

Customer supplies the materials for the ribbon 

board.

RIBBON BOARD REQUIRED: ROLL-UP SIDES

A customer-supplied ribbon board is required for the 

installation of the roll-up curtain. Fasteners are included. 

Customer supplies the materials for the ribbon board.

DIAGRAMS ARE NOT TO SCALE.

The diagram 

shows a customer-

supplied ribbon 

board as attached 

to the frame.

Diagram applies to 

buildings equipped 

with drop-down 

side curtains.

2" x 6" 

Board

U-Channel

(102197)

End View

1/4" Nut 

(FALB01B)

& 

Washer  

(FAMF01B)

1/4" x 4" Carriage 

Bolts (FAH009B)

FA4652 Wood 

Screws

Rafter Leg

ATTENTION:

 The position of the side ribbon board 

for buildings with either drop-down or roll-up sides 

can be lowered a few inches to overlap the purlin 

clamp. This allows the board to remain on the straight 

part of the rafter. 

Rafter

2" x 6" Board

1" x 4" Board 

FA4652 

Wood 

Screws

1/4" x 4" 

Carriage 

Bolts 

(FAH009B), 

1/4" flat 

washers, 

and 

FALB01B 

1/4" nuts.

U-Channel

102197

Summary of Contents for Gro-Max 108179H






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands