ClearSpan Gro-Max 108179H Manual Download

Page: 50 / 53

Revision date: 09.18.14

CLEARSPAN

™

GRO-MAX GOTHIC HIGH TUNNELS

END FRAMING - CONNECTION DET

AILS

106755

1/2"

Bolt

1/2"

Bolt

Assemb

Guid

Customer

This

Side

Screws

Wood

lied

107923

3/8"

Thre

aded

Guid

Rafter

ield

Wash

lied

Customer

ATTENTION:

Panel is not shown. Sink

threaded rod below the surface of the customer-supplied end wall post. See details on page 15.

Threaded rod and rafter are not shown. Roll-up door panel is not shown.

104188B 1/2" bolt, FALB08B nut, & FAME09B washer

FAK16 ROD (cut), FALB04B nuts & FAME08B washer

CUST

OMER-SUPPLIED END FRAME:

Construct the end

frame for the roll-up end panel using 4" x 4" wood posts. The doorframe materials are supplied by the customer

If quality 4" x 4" lumber at the lengths needed is not available, construct 2-ply wood beams using 2" x 6" boards secured together with exterior grade bolts and nuts. Center the doorframe in the end wall and dig the holes for the doorjambs.

Stagger all joints. Do not align.

Use treated lumber and

set in concrete for best results.

Summary of Contents for Gro-Max 108179H






















































Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands

ClearSpan Gro-Max 108179H, Manual

Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands