ClearSpan Gro-Max 108179H Manual Download | Manualshive

Page: 23 / 53

background image

23

Revision date: 09.18.14

CLEARSPAN

™

GRO-MAX GOTHIC HIGH TUNNELS

FRAME CHECK

Before you attach the side curtains, inspect the frame for

sharp edges or fasteners that could damage the curtain or

kit components.
1.  Verify that all frame members are properly secured.
2.  Verify that all bolts and clamps are tight.
3.  Recheck the frame assembly for sharp edges or

clamps and bolts that may interfere with the installation

of the curtain. File or tape sharp edges as needed.

4. Reposition clamps and bolts as needed and tape all

rafter pipe joints with duct tape to protect the curtain.

5. Verify that the main building frame is properly and

adequately anchored.

Do not attach the side curtains to an unanchored

frame.

6. Continue by installing the side curtains and

components.

INSTALL THE DROP-DOWN SIDES

If your building includes roll-up sides, go to and complete

the

"Install Roll-Up Sides"

procedure.

Do not continue

with these drop-down curtain steps.

Locate these parts to attach the pulleys and drop-down

curtain axle:
• 131S075 (1.315 swaged pipe for axle) and 131P0XX

(where XX represents the length needed to complete

the axle assembly). See side profile for pipe

identification if needed.

•  106734 band clamp
•  103496 gearbox and 103544 mounting plate
•  102717 double drive
•  FA4482B Tek screws (for axle conduit)
•  FAH009B (1/4" x 4" carriage bolts) and FALB01B (1/4"

nuts)—use with FAME50B flat washers on the nut side.

• FAH005B (1/4" x 2" hex head bolts)
• FALF15B (1/4" lock nut) and FAME50B (1/4" flat

washer)—used to secure the mounting plate.

Continue with the steps that follow to install the drop-down

curtain components.

1. Take the 103544 mounting plate (shown above) and

move outside the end wall where you want to position

the gearbox.

103544 Mounting Plate (Figure 1)

Actual mounting plate may differ from what is shown

.

Gearbox Mounting

Holes

Axle Hole

Plate Mounting

Holes

«
...
21
22
23
24
25
...
»

Summary of Contents for Gro-Max 108179H






















































Reviews:

No comments

Related manuals for Gro-Max 108179H

Brand: Absco Pages: 37

Safari Stingray 3-Person Tree Tent

Brand: Tentsile Pages: 17

Brand: Crivit Pages: 38

Brand: Coleman Pages: 2

Brand: ZANE ARTS Pages: 16

Brand: skandika outdoor Pages: 4

Canopy Gotland 4

Brand: Skandika Pages: 2

Brand: Inventini Pages: 13

Brand: Coolaroo Pages: 6

Brand: Gorilla Pages: 6

Castle Pop-Up Tent

Brand: Oypla Kids Pages: 2

Brand: NRS Relief Pages: 2

Brand: Outdoor Revolution Pages: 2

Brand: Yarden Pages: 20

Serre Tunnel 9m2

Brand: LAMS Pages: 2

Brand: Palram Pages: 61

Brand: Coleman Pages: 2

Brand: ABSCO SHEDS Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands