ClearSpan Gro-Max 108179H Manual Download

Page: 26 / 53

Revision date: 09.18.14

CLEARSPAN

™

GRO-MAX GOTHIC HIGH TUNNELS

NOTE:

To prevent damage to the end panels,

not allow the free end of the axle to touch the inside

surface of the end wall. Trim pipe if needed. Axle must

turn freely.

18. After installing all sections of axle conduit for the first

drop-down curtain assembly, verify that the axle conduit

is level and that each conduit splice is secured with a

Tek screw (Step 14).

19. Move to the gearbox and test the assembly using the

crank handle.

NOTE:

The assembled axle conduit should turn freely

throughout the length of the shelter. Adjust the band

clamps as needed. Reposition clamps and screws if

these prevent smooth operation of the axle conduit.

20. After verifying that the axle turns smoothly, repeat the

procedure to assemble and attach the gearbox and

axle conduit

to the other side of the shelter.

21. Continue by preparing and attaching the drop-down

curtains to the frame and axle conduit of both drop-

down assemblies.

INSTALL THE DROP-DOWN CURTAIN (continued)

Locate these parts to prepare the drop-down curtain for

installation and to attach it to the axle conduit:
•  131S075 pipe conduit
•  CC5505 (1/8" curtain cord)
•  FA1960 (3/16" x 3" eye screw)
•  AS5020 pulleys
•  Duct tape
•  Drop-down curtain (Panel ID begins with DD.)

Attach Drop-Down Curtain Pulleys

Continue with the steps that follow:
1. Gather the pulleys and the same quantity of 3" eye

screws (FA1960) and move to the inside of the shelter.

2. Slide one pulley onto the threaded shaft of the eye

screw and twist the eye screw into the ribbon board

4"-6" on either side of the first rafter to secure the

pulley.

NOTE:

Position the eye screw and pulley 4-6 inches

away from the rafter on either side of the rafter.

Pulley should hang freely from the eye screw.

Do not

overtighten the screw.

3. Move to the next rafter and repeat the steps to install

another pulley.

Install one pulley for each rafter along

each side of the frame.

4. Continue installing eye screws and pulleys into the

ribbon board

next to each rafter

until all pulleys are

installed

along both sides of the shelter

5. Install the curtain conduit and attach cords as

described in the next procedure.

Ribbon Board

As seen from

the inside.

Cover Material

Summary of Contents for Gro-Max 108179H






















































Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands

ClearSpan Gro-Max 108179H, Manual

Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands