ClearSpan Gro-Max 108179H Manual Download Page 7

Page: 7 / 53

Revision date: 09.18.14

CLEARSPAN

™

GRO-MAX GOTHIC HIGH TUNNELS

Swaged

Plain

102198

U-Channel Spring

103496

Gearbox

102856

End Clamp

FA4482B

Tek Screw

102717

Gearbox Drive

103544

Mounting Plate

102921

Neo-bonded Galvanized

Washers

QH1402

Band Clamp

102197

Aluminum

U-Channel

102548

Cross Connector

FAH009B & FALB01B

Carriage Bolt & Hex Nut

106734 Band Clamp

(drop-down sides only)

AS5020 Pulley

(drop-down sides only)

The following graphics and photos will help you identify the

different parts. (Some parts are not shown.)

Swaged and Plain Rafter Sections

MATERIAL IDENTIFICATION NUMBERS FOUND ON THE BILL OF MATERIALS

•

D10025824M

—A 6' x 8' panel used to create four (4) wind panels (2' x 6' each)—one for each corner of the frame for

dropdown sides only. Material can be used to winterize the corners of buildings with rollup sides if desired.

•

DCC4931

—This number identifies the bulk material used to cover the open areas of the end frame and door frame:

See End Panel Location diagram in the Quick Start section of this guide.

•

DD084HxxxCN52

—This number identifies the panels used for the drop-down or roll-up curtain along each side. There

are two identical panels. The xxx in the number represents the length of each panel, which is specific to each building.

•

QED108181

— This sku represents the material used for the 16'W x 10'H roll-up doors for all 20' wide buildings. There

are two (2) panels of identical dimensions. These panels include a pocket at the bottom and installed grommets along

each side. The top of the panel, which is attached to the door frame, is plain.

•

Main Cover

—

Buildings

with the

identification number (e.g., 108179

D) have a 5.2 oz clear fabric main cover;

cover part number begins with the letters

Buildings

with the

identification number (e.g., 108179

D) include

a film cover identified by a six digit sku number; there are no letters in the film identification number.

Summary of Contents for Gro-Max 108179H






















































Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Brands by name

Popular brands

ClearSpan Gro-Max 108179H, Manual

Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Brands by name

Popular brands