ClearSpan Gro-Max 108179H Manual Download

Page: 6 / 53

Revision date: 09.18.14

CLEARSPAN

™

GRO-MAX GOTHIC HIGH TUNNELS

REQUIRED TOOLS

The following list identifies the main tools needed to

assemble the shelter. Additional tools and supports may be

needed depending on the structure, location, and

application.
•  Tape measure or measuring device
•  Marker to mark locations on the pipes
•  Variable speed drill and impact driver (cordless with

extra batteries works best)

• Metal-cutting saw
• Wrenches and impact socket set, or an adjustable

wrench

•  Scissors, utility knife, or tin snips
•  Hammers, gloves and eye protection
•  Adjustable pliers and self-locking pliers
•  Ladders, work platforms, and other machinery for lifting

designed to work safely at the height of the building

UNPACK AND IDENTIFY PARTS

The following steps will ensure that you have all the

necessary parts

before

you begin to assemble the shelter

frame.
1. Unpack the contents of the shipment and place where

you can easily inventory the parts. Refer to the Bill of

Materials/Spec Sheets.

2. Verify that all parts listed on the Bill of Materials/Spec

Sheets are present. If anything is missing or you have

questions, consult the Pictorial Parts Guide and all

diagrams for clarification, or contact Customer Service.

NOTE:

At this time, you do not need to open the plastic

bags containing smaller parts such as fasteners or

washers (if equipped).

Customer Notes

BUILDING IDENTIFICATION

All buildings are identified by a building sku number

(e.g., 108179

HCD

). Use the following information to

determine the cover and side curtain specifics of your

building.

•

HCD: Film cover with Drop-Down Sides

•

HFD: 5.2 oz cover with Drop-Down Sides

•

HCRU: Film cover with Roll-Up Sides

•

HFRU: 5.2 oz cover with Roll-Up Sides

Summary of Contents for Gro-Max 108179H






















































Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands

ClearSpan Gro-Max 108179H, Manual

Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands