ClearSpan Gro-Max 108179H Manual Download

Page: 28 / 53

Revision date: 09.18.14

CLEARSPAN

™

GRO-MAX GOTHIC HIGH TUNNELS

INSTALL THE DROP-DOWN CURTAIN (continued)

9. Locate the 1/8" curtain cord (CC5505) and cut a

section of cord to the length determined in the previous

step.

10. Beginning at one end of the frame, move to the curtain

conduit in the curtain pocket, and make a small cut in

the material

below

the conduit and in line with a pulley.

11. Insert the end of the cord through the opening in the

curtain and tie the cord to the conduit.

12. Take the free end of the cord, thread it through the

pulley,

wrap it over and around the axle conduit,

and

temporarily tie it to the axle conduit.

NOTE:

Verify that the cord is properly aligned with the

pulley and with the other end of the cord tied to the

curtain conduit.

The cord must remain aligned for proper curtain

operation.

13. Drive two (2) FA4482 Tek screws with neo-bonded

washers (102921) into the axle conduit where the

cord is located.

Do not fully seat the Tek screws to the

conduit.

Allow space to remain between the washer

and conduit.

14. Verify that the curtain conduit remains against the

baseboard and pull the slack from the cord.

15. Weave the cord around the Tek screws as shown and

tighten the screws to secure the cord to the axle.

16. Move to the next pulley position and repeat the steps

to measure, cut, and attach another cord to the curtain

and axle conduit.

ATTENTION:

If the cord length was correct for the first,

cut additional cords to the same length. To ensure that

the curtain remains level during operation, verify that

additional cords are wrapped around the axle conduit

in the same direction as the first cord. Continue this

pattern for all remaining cord-to-axle connections.

Cord

Conduit in

Curtain Pocket

Knot

Curtain

FA4482 Tek Screws with

102921 Neo-Bonded Washers

Summary of Contents for Gro-Max 108179H






















































Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands

ClearSpan Gro-Max 108179H, Manual

Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands