background image

2.5 X 4.5 X 2.5M FOLDABLE STEEL GARAGE 

EXTENSION

MODEL NO: 

FGE01

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

 

9

   Read all safety instructions to reduce the risk of injury or death.

 

9

   This is a temporary structure and is not recommended as a permanent structure.

 

9

   Choose your shelter’s location carefully. Check for overhead utility lines, branches, etc. 

DO NOT

 install near roofs or other structures  

  that may shed snow, ice or excessive run-off onto your shelter. Keep away from electrical wires!

 

9

   Install your shelter on a level surface.

 

9

   Check municipal by-laws prior to setting up the product.

 

9

   Have an overview of all parts before attempting installation. Make sure all components are available.

 

8

  

DO NOT

 use this product in environments for which it is not intended (i.e. extreme cold, high winds, extreme heat, heavy rainfall,   

 etc).

 

9

   Always wear safety glasses when assembling this product. Wear gloves when working with tubing to prevent cuts or abrasions.

 

9

   Anchors must be used with all shelters. Covers should 

NOT

 be installed on any product until it has been properly anchored to the  

 ground.

 

9

   Proper anchoring and keeping cover tight and free of snow and debris, is the responsibility of the consumer.

 

9

   Damages caused by improper anchoring are not covered under warranty.

 

9

   Keep all flame and heat sources away from the shelter fabric. The fabric will burn if left in continuous contact with a flame source.

 

8

  

DO NOT

 use open flames or cooking or heating devices inside or in close proximity to the product, including all types of stoves, gas  

  heaters, gas lanterns, citronella torches, mosquito coils, etc.

 

8

  

DO NOT

 cook, smoke, refuel or use any open flame devices in or around the shelter.

 

8

  

DO NOT

 store flammable liquids (gasoline, kerosene, propane, etc.) in the shelter.

 

8

  

DO NOT

 operate gas powered vehicles/equipment in or around the shelter.

 

9

   Keep open flames a safe distance away from the shelter.

 

8

  

DO NOT

 use hard-edged tools or instruments, such as rakes or shovels, to remove snow. These can cause punctures to the cover.

 

8

   DO  NOT

 start the engine of any vehicle or machine inside a closed shelter. Ensure that there is adequate ventilation for starting    

  engines and for any work with paints, cleaners, etc.

 

9

   This shelter is 

NOT

 designed to support heavy snow or ice loads. Snow or ice accumulation may cause your shelter to collapse. To  

  avoid overload, brush snow and ice off the roof top with a broom or mop.

 

9

   To prevent collapse, damage to property, personal injury and/or death, NEVER clear the roof of snow or debris from inside the    

 shelter.

 

9

   Keep children away during assembly. This product contains small parts which can be swallowed by children.

 

8

   DO  NOT

 attempt to assemble the product if any parts are missing.

 

9

   At least 4 people are needed to complete the assembly as some of the steps require heavy lifting.

 

‰

  

WARNING! DO NOT

 leave the shed unattended during assembly. Otherwise, personal injury or damage to the shed may occur

2.  INTRODUCTION

Foldable garage extension, perfect for allowing temporary use of a driveway as a garage. Supplied with a powder coated steel frame. 195g/m2 

PE Tarp with UV protection and completely waterproof.

3.  SPECIFICATION

Model No:...................................................................FGE01

Door Size: .................................. 2500mm (W) x 2000mm (H)

Material: ......................................195g/m2 PE Tarp and Steel

Overall Size (W x D x H): ..............................2.5 x 4.5 x 2.5m

FGE01 Issue 1 25/11/2020

Original Language Version

© Jack Sealey Limited

Refer to 

instructions

 Wear eye 

protection

 Wear protective 

gloves

 Wear safety 

footwear

Summary of Contents for FGE01







Reviews: