manualshive.com logo in svg

ClearSpan Gro-Max 108179H, Manual

Share
Download
ClearSpan Gro-Max 108179H Manual Download Page 14

14

Revision date: 09.18.14

CLEARSPAN

™

 GRO-MAX GOTHIC HIGH TUNNELS

SIDE STRUT INSTALLATION

There are four (4) side struts for the shelter. These struts 

are positioned between the end rafters and the first interior 

rafter on each side of the shelter.

Complete these steps to install the four (4) side struts:

Gather the parts:
•  Struts (QH1304)
•  Band Clamps (#QH1402) 

1.  Locate one strut and position it between one end rafter 

leg and the leg of the first interior rafter as shown 

below.

Strut (QH1304)

End Rafter

Interior

Rafter

Customer supplies the 

baseboard. Baseboard 

is installed later. 

Position strut so it 

will not interfere with 

the installation of the 

baseboard.

Ground Level

2.  Attach one end of the strut to the band clamp as shown 

in the diagram below. 

Strut

End Rafter

Band Clamp

3.  Attach the remaining end of the strut to the added band 

clamp on the first interior rafter. See the diagram that 

follows for location. 

4.  Repeat the above steps to attach the remaining side 

struts to the shelter.

5.  After securing the struts, verify that all clamps are 

secured with a Tek screw to the rafters.

6.  Verify that each pipe splice (purlin and rafter) is 

secured with a Tek screw.

7.  Complete the next procedure to anchor the assembled 

frame.

NOTE:

 Head of bolt on the band clamp must face 

toward the outside of the shelter.

Attach strut 

as shown.

Interior 

Rafter

Ground Level

Baseboard

Inside of 

frame.

ANCHOR THE ASSEMBLED FRAME

At this point, anchor the high tunnel frame. Consult the 

MUST READ document for anchoring information and 

suggestions. Please call customer service at 1-800-245-

9881 for additional anchoring information.

CAUTION

: The anchor assembly is an integral part of

the high tunnel construction. Improper anchoring may 

cause instability and failure of the structure to perform 

as designed. Failing to anchor the shelter properly 

will void the manufacturer’s warranty and may cause 

serious injury and damage.

After reading the MUST READ document and anchoring 

the frame, continue by installing the customer-supplied end 

frame for the door.

The diagrams shown in the MUST READ document 

show frames with mounting feet. The anchor methods 

also apply to buildings equipped with ground posts.

 

Summary of Contents for Gro-Max 108179H






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands