ClearSpan Gro-Max 108179H Manual Download

Page: 53 / 53

Revision date: 09.18.14

CLEARSPAN

™

GRO-MAX GOTHIC HIGH TUNNELS

Photo shows the fully assembled

drop-down curtain from the inside

of a sample shelter.

Axle Conduit held

in place by 106734

band clamps.

Ribbon Board

Drop-down curtain assembly as

seen from the inside.

106734 Band Clamp

Pulley

Rope

Baseboard

The above photo shows a typical drop-down side curtain as installed on a sample building. This photo applies to

buildings equipped with drop-down sides only. It does not apply to buildings equipped with roll-up sides.

ADDITIONAL PHOTOS PAGE

The above photo shows how to secure the angled purlin to the underside of the assembled rafters and frame. Use

FA4482B Tek screws and QH1070 pipe straps.

End Rafter

Interior Rafter

End of purlins

at interior

rafter.

Summary of Contents for Gro-Max 108179H






















































Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands

ClearSpan Gro-Max 108179H, Manual

Search results

Summary of Contents for Gro-Max 108179H

Reviews:

Related manuals for Gro-Max 108179H

Brands by name

Popular brands