Cisco WRP500 Administration Manual Download Page 48

Page: 48 / 128

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

A-4

Cisco WRP500 Administration Guide

Appendix A Advanced Voice Fields

Info page

Call 1 and 2 Type

Direction of the call. May take one of the following values:

•

PSTN Gateway Call = VoIP-To-PSTN Call

•

VoIP Gateway Call = PSTN-To-VoIP Call

•

PSTN To Line 1 = PSTN call ring through and answered by Line 1

•

Line 1 Forward to PSTN Gateway = VoIP calls Line 1 then forwarded
to PSTN GW

•

Line 1 Forward to PSTN Number =VoIP calls Line 1 then forwarded
to PSTN number

•

Line 1 To PSTN Gateway

•

Line 1 Fallback To PSTN Gateway

Call 1 and 2 Remote
Hold

Indicates whether the far end has placed the call on hold.

Call 1 and 2 Callback

Indicates whether the call was triggered by a call back request.

Call 1 and 2 Peer
Name

Name of the internal phone.

Call 1 and 2 Peer
Phone

Phone number of the internal phone.

Call 1 and 2 Call
Duration

Duration of the call.

Call 1 and 2 Packets
Sent

Number of packets sent.

Call 1 and 2 Packets
Recv

Number of packets received.

Call 1 and 2 Bytes
Sent

Number of bytes sent.

Call 1 and 2 Bytes
Recv

Number of bytes received.

Call 1 and 2 Decode
Latency

Number of milliseconds for decoder latency.

Call 1 and 2 Jitter

Number of milliseconds for receiver jitter.

Call 1 and 2 Packets
Lost

Number of packets lost.

Call 1 and 2 Packet
Error

Number of invalid packets received.

Call 1 and 2 Mapped
RTP Port

The port mapped for Real Time Protocol traffic for Call 1/2.

Call 1 and 2 Media
Loopback

Media loopback is used to quantitatively and qualitatively measure
the voice quality experienced by the end user.

Summary of Contents for WRP500

































































































































Search results

Summary of Contents for WRP500

Reviews:

Related manuals for WRP500

Brands by name

Popular brands

Cisco WRP500, Administration Manual

Search results

Summary of Contents for WRP500

Reviews:

Related manuals for WRP500

Brands by name

Popular brands