Names and Functions
Front View
Rear View
Ethernet Port
DC Input
Ethernet Port (PoE)
Factory Reset Switch
Console Port
Dust covers are installed on power ports (DC 48 V/0.75 A), Ethernet ports and console ports
(CONSOLE). Remove the covers before use.
Interface
Port Name
Description
Status LED
Displays the status information of the WEA400/500 Series via LED.
DC Input
Used when a power adapter is used for power supply.
Ethernet Port (PoE) Supports 1000 BASE-T Gigabit Ethernet and PoE IEEE
802.3af/802.3at.
Ethernet Port
Supports 1000 BASE-T Gigabit Ethernet.
Console Port
Used for checking the operational status of the WEA400/500 series
and for CLI input.
Factory Reset
Switch
Used for initialization when commencing factory shipment of the
WEA400/500 series.
Status LED
Introduction
What is the WEA400/500 series?
The WEA400/500 is a series of APs fromthe Samsung WE wireless LAN family.
They connect a UE such as a smart phone, a tablet PC or a laptop that supports the
wireless LAN to a wired network. The WEA400/500 series supports the following features:
- IEEE 802.11a/b/g/n/ac standard
- PoE (Power over Ethernet) IEEE 802.3af/802.3at
- WEA412i: 2 × 2 MIMO (Multiple Input Multiple Output)
- WEA403i/403e/413i: 3 × 3 MIMO (Multiple Input Multiple Output)
- WEA504i/514i: 4 × 4 MU-MIMO (Multi User-Multiple Input Multiple Output)
- Wireless LAN through both 2.4 GHz and 5 GHz bandwidth simultaneously
- WEA403Si supports the connection of various sensors and equipment to a network with
WLAN, BLE, ZigBee.
Components
After unpacking the WEA400/500 series, check whether all of the following components
are included.
WEA403i/412i/413i/403Si/504i/514i
WEA403e
Common merchandise
Mounting Bracket
5 M3 × L6 screws
(Including 1 spare)
Installation Manual
Security Torx (T10) Screw
Plastic 4 anchors
M4 × L28 4 screws
- It is recommended to keep all packaging materials and the box.
- The power adapter and the external antenna for WEA403e are sold separately.
When necessary, please contact the place of purchase.
This manual describes the configuration of the Wireless Enterprise WEA400/500 series and
its installation procedures.
The installation procedures are described based on the WEA403i/412i/413i/403Si/504i/514i configurations.
The same installation procedures apply to the WEA403e model, except for the antenna installation.
Installation
The WEA400/500 series can be installed on ceilings or walls.
Please check whether all the components are included before installation.
Before Installation
Safety Requirements
Risks may be caused when the following safety warnings are not properly observed.
For safe use, make sure to be well-informed.
- There is an electrical risk with the product. Make sure that the power is off during installation
and do not proceed with the installation when there is current leakage. Use of products with
current leakage may cause serious electrical shock to the user.
- Wear anti-static gloves or take appropriate actions to prevent ESD when handling the product.
- This product must be connected to ta power supply in compliance with IEEE 802.3af/at or to a
limited power supply in compliance with IEC/EN/UL 60950-1.
- This product must be installed or removed only by appropriately-trained service personnel.
- This product operates with SELV (Safety Extra Low Voltage) according to IEC/EN/UL 60950-1.
- All interconnecting equipment including this product must be installed within the same
building. For details, refer to Environment A of IEEE 802.3af/at standard.
- This product must be installed with at least 3 m or more distance from the WiMAX/3G/4G
repeater or antenna.
Installation Instructions
The instructions below must be followed when installing.
- It must be installed in a place that can be easily accessed for product installation, cable
connection and maintenance.
- The PoE LAN cable must be always installed away from any electrical interference
source such as power lines, fluorescent lights or transmitters.
- The PoE LAN cable must be CAT 5E or higher.
- When PoE is unavailable, a power adapter (sold separately) can be used. The 3-pin
(including ground) power socket that supplies 100~240 V AC, 50~60 Hz must be
located within 2 m from each equipment and the power must be supplied through an
independent circuit breaker. It is recommended to use the equipment that uses a filter
or a surge.
Installation on Ceilings (When the ceiling type is T-bar)
- When incorrectly installed on the ceiling, the WEA400/500 series may drop onto a person or
equipment. Therefore, make sure to fix it firmly.
- If the ceiling type is not T-Bar, please refer to the ‘Installation Manual’ provided separately.
For this installation manual, please contact the dealer.
1.
Remove the holding tape that was attached to fix the ceiling clip.
Holding tape
2.
Open the ceiling clip so that it is wider than the width of the T-bar.
3.
Move the ceiling clip so that it is appropriate for the T-bar width.
Status LED
LED
Status
Description
System start
status
White On
Initial LED status
Blue On
Device reset and test in progress
Red On
Booting failure (Device reset failure)
Provisioning
Status
Red, green and off
repeated
APC connection in progress
(Network link normal)
Green blinking
CAPWAP connection in progress
(APC server connection normal)
Normal
operation status
Green On
When there is no connected wireless UE
Blue On
When there is a connected wireless UE
Upgrade
Green blinking
Software upgrade in progress
Error status
Red blinking
Physical connection error of network
Yellow blinking
IP address conflict
Purple blinking
Dynamic IP address allocation failure
Bluish-green blinking
Logical connection error of network
Red, green and off
repeated
Wireless interface error
WEA400/500 Series (Indoor) Quick Installation Manual
