Cisco WRP500 Administration Manual Download Page 51 | Manualshive

Page: 51 / 128

background image

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

A-7

Cisco WRP500 Administration Guide

Appendix A Advanced Voice Fields

SIP page

DTMF Relay MIME
Type

MIME Type used in a SIP INFO message to signal a DTMF event.

The default is

application/dtmf-relay

.

Remove Last Reg

Lets you remove the last registration before registering a new one if
the value is different. Select yes or no from the drop-down menu.

The default is

no

.

Use Compact Header Lets you use compact SIP headers in outbound SIP messages.

Select yes or no from the drop-down menu. If set to yes, the
WRP500 uses compact SIP headers in outbound SIP messages. If
set to no, the WRP500 uses normal SIP headers. If inbound SIP
requests contain compact headers, the WRP500 reuses the same
compact headers when generating the response regardless the
settings of the

Use Compact Header

parameter. If inbound SIP

requests contain normal headers, the WRP500 substitutes those
headers with compact headers (if defined by RFC 261) if

Use

Compact Header

parameter is set to yes.

The default is

no

.

Escape Display Name Lets you keep the Display Name private. Select yes if you want the

WRP500 to enclose the string (configured in the Display Name) in
a pair of double quotes for outbound SIP messages. Any
occurrences of or \ in the string is escaped with \ and \\ inside the
pair of double quotes. Otherwise, select no.

The default is

no

.

RFC 2543 Call Hold

Configures the type of call hold: a:sendonly or 0.0.0.0.

The default is

no

; do not use the 0.0.0.0 syntax in a HOLD SDP; use

the a:sendonly syntax.

Mark All AVT Packets If set to yes, all AVT tone packets (encoded for redundancy) have

the marker bit set. If set to no, only the first packet has the marker
bit set for each DTMF event.

The default is

yes

.

SIP TCP Port Min

Specifies the lowest TCP port number that can be used for SIP
sessions.

SIP TCP Port Max

Specifies the highest TCP port number that can be used for SIP
sessions.

«
...
49
50
51
52
53
...
»

Summary of Contents for WRP500

































































































































Reviews:

No comments

Related manuals for WRP500

DWL-AG700AP - AirPlus AG - Wireless Access...

Brand: D-Link Pages: 59

DWL-3260AP - AirPremier - Wireless Access...

Brand: D-Link Pages: 57

Powerline MD 90222

Brand: Medion Pages: 124

Brand: M Box Pages: 60

Brand: Modecom Pages: 48

Brand: ICP DAS USA Pages: 61

SCALANCE W734-1

Brand: Siemens Pages: 64

ARS-7235-PSE-AC Series

Brand: ANTAIRA Pages: 24

Brand: Draytek Pages: 140

Brand: LevelOne Pages: 49

Brand: Credo mobile Pages: 6

Brand: ELTEX Pages: 74

Brand: Skullcandy Pages: 1

airFiber AF-11FX

Brand: Ubiquiti Pages: 47

Brand: Krüger & Matz Pages: 28

Brand: Cambium Networks Pages: 2

Brand: Black Box Pages: 59

Brand: Zio Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands