Cisco WRP500 Administration Manual Download Page 18 | Manualshive

Page: 18 / 128

background image

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

1-12

Cisco WRP500 Administration Guide

Chapter 1 Product Overview and Deployment Guidelines

Remote Provisioning

Resync URL

The WRP500 can be configured to automatically resync its internal configuration state to a remote
profile periodically and on power up. The automatic resyncs are controlled by configuring the desired
profile URL into the device.

The Resync URL lets you force the WRP500 to do a resync to a profile specified in the URL,
which can identify either a TFTP, HTTP, or HTTPS server. The syntax of the Resync URL is as
follows:

http://

WRP500_ip_address

/admin/resync?[[protocol://][server-name[:port]]/profile-pathname]

Note

The WRP500 resyncs only when it is idle.

If no port is specified, the default port is used (69 for TFTP, 80 for HTTP, and 443 for HTTPS).

The profile-path is the path to the new profile with which to resync, for example:

http://192.168.2.217/admin/resync?tftp://192.168.2.251/spaconf.xml

Reboot URL

The Reboot URL lets you reboot the WRP500. The Reboot URL is as follows:

http://

WRP500_ip_address

/admin/reboot

Note

The WRP500 reboots only when it is idle.

Configuration Profile

Because the WRP500 has two sets of parameters, one set for data and one set for voice, the
requirements vary from the provisioning of other Cisco Small Business IP Telephony Devices.
You will have two profiles: one for the data (router) parameters and one for the voice parameters.
One benefit of having separate profiles for voice parameters and data parameters is that you can
deploy the common data parameters to all of your customer sites and deploy the custom voice
parameters to each site individually.

•

Data (router) parameters:

Use the XML format only, as described in the

Provisioning Guide

. For

more information about the data parameters, see

Appendix B, “Data Fields.”

•

Voice parameters:

Use the XML format. The binary format is generated by a profile compiler tool

available from Cisco. Find the correct SPA Profiler Compiler (SPC) for the firmware that you have
installed on your WRP500. For more information about the data parameters, see

Appendix A, “.”

Note

You can download the SPC at the following URL:

tools.cisco.com/support/

downloads/go/Redirect.x?mdfid=282414113

«
...
16
17
18
19
20
...
»

Summary of Contents for WRP500

































































































































Reviews:

No comments

Related manuals for WRP500

Brand: ZyXEL Communications Pages: 15

Brand: NetComm Wireless Pages: 2

Brand: P-Com Pages: 54

Brand: Ubiquiti Pages: 61

Wireless Hotspots HSv210

Brand: Check box Pages: 36

Brand: wattsonic Pages: 60

Brand: TRENDnet Pages: 58

Transit Buds HX-EP310

Brand: Jam Audio Pages: 2

Brand: Arista Pages: 4

Brand: Arista Pages: 4

Brand: Harman Pages: 23

Brand: Miiego Pages: 20

TG-RouterE-PM-01-100

Brand: Telegesis Pages: 9

Brand: H3C Pages: 69

Brand: Allied Telesis Pages: 180

Brand: T-Mobile Pages: 4

Brand: T-Mobile Pages: 13

Brand: T-Mobile Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands