Cisco WRP500 Administration Manual Download Page 104 | Manualshive

Page: 104 / 128

background image

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

B-14

Cisco WRP500 Administration Guide

Appendix B Data Fields

Wireless Configuration

Wireless > Wireless MAC Filter

WPA Enterprise and WPA2 Enterprise:

•

WPA Algorithms: The encryption method for
dynamic encryption keys. For WPA Enterprise, the
options are AES or TKIP (default). For WPA2
Enterprise, the options are AES or TKIP+AES
(default).

•

RADIUS Server Address: The IP address of the
RADIUS server to be used for authentication.

•

RADIUS Port: The port number of the RADIUS
server. The default value is 1812.

•

Shared Key: The key shared to be used to establish
a connection between the WRP500 and the server.

•

Key Renewal Timeout: The period of time in
minutes that can elapse before the WRP500
changes the encryption keys.
Default: 600 seconds (10 minutes)

SSID

The network name of the network for this MAC filter.

Wireless MAC Filter

When this feature is enabled, the specified Access
Restriction is applied to the specified clients. When this
feature is disabled, access is not filtered by MAC
address.

Default: Disabled

Access Restriction

Prevent: Devices in the MAC Address Filter List are
prevented from connecting to the specified wireless
network.

Permit: Only devices in the MAC Address Filter List
are allowed to connect to the specified wireless
network.

MAC Address Filter List
MAC 01 through MAC 40

The MAC address of each machine that is subject to the
specified access restrictions.

«
...
102
103
104
105
106
...
»

Summary of Contents for WRP500

































































































































Reviews:

No comments

Related manuals for WRP500

Brand: Majesti-Fi Pages: 2

Brand: D-Link Pages: 3

Brand: Watchguard Pages: 2

EliteConnect SMC2555W-AG2

Brand: SMC Networks Pages: 2

Brand: Contec Pages: 111

SpeedNet SDR Series

Brand: S&C Pages: 16

Brand: ALCON Pages: 47

SOUNDFLOW i17 +

Brand: WEEPLUG Pages: 22

Brand: Technicolor Pages: 61

Brand: Zte Pages: 32

Wi-REACH Classic

Brand: Connect One Pages: 38

Brand: XtendLan Pages: 23

Brand: Sony Pages: 3

Brand: EnGenius Pages: 58

Brand: Broadxent Pages: 27

AirVelocity 1500

Brand: Airspan Pages: 36

Brand: Zalip Pages: 64

Brand: Sapido Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands