Cisco Linksys SPA9000 Administration Manual Download

Page: 270 / 286

SPA400 Field Reference

Setup

SPA9000 Voice System Administration Guide

268

Setup tab>

Voicemail Server

Voicemail Settings

Server Port

The UDP port this is open to receive packets

NOTE

This port number must be different from the

signaling port on the SPA9000 line interface. This port
appears in the various mailbox URL fields on the SPA9000
line interface page.

Default:

5090

SPA9000 subscriber ID

The ID that the SPA9000 uses to subscribe to the SPA400
voice mail server to obtain notifications

NOTE

This value appears in the

Proxy and Registration:

Mailbox Subscribe URL

field on the SPA9000 line

interface page.

Example

•

SPA9000 subscriber ID:

8888

•

Mailbox Subscribe URL:

[email protected]:5090

Default:

8888

Mailbox deposit number

The phone number that the SPA9000 uses to deposit voice
mail

NOTE

This value appears in the

Proxy and Registration:

Mailbox Deposit URL

field on the SPA9000 line interface

page.

Example

•

Mailbox deposit number:

900

•

Mailbox Deposit URL:

[email protected]:5090

Default:

900

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for Linksys SPA9000































































































































































































































































































Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands

Cisco Linksys SPA9000, Administration Manual

Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands