manualshive.com logo in svg

Cisco Linksys SPA9000, Administration Manual

The Cisco Linksys SPA9000 is an advanced communication system designed for small businesses. Ensure smooth operation with the Administration Manual, available for free download from manualshive.com. This comprehensive manual covers setup, troubleshooting, and customization, empowering users to harness the full potential of this powerful product.

Share
Download
background image

SPA9000 Field Reference

Voice tab

SPA9000 Voice System Administration Guide

216

B

 

Voice tab > SIP page

Internal Music Source Parameters section

Internal Music URL 

URL from which to download a music file to be used by the 
parking lot. The format is: 

[tftp://]server-ip-addr[:port]/path 

TFTP is the only protocol supported for music download. 
Default port is 69. Changing the value of this parameter from 
the web interface triggers a graceful reboot of the SPA9000. 
If a valid entry is specified, the SPA9000 attempts to 
download the file on bootup and store the samples in flash 
memory. The SPA9000 remembers the link where the stored 
file is downloaded and does not try to download again on the 
next reboot. 

The music samples are encoded in G711u format at 8000 
samples/second. The file should not contain any extra 
header information. Maximum length of the file is 65.536 
seconds (524288 bytes). 

Default: blank

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for Linksys SPA9000































































































































































































































































































Reviews:

No comments

Related manuals for Linksys SPA9000

ICP DAS USA HRT-310 Quick Start Manual preview
HRT-310
Brand: ICP DAS USA Pages: 7
ICP DAS USA UA-5200 Series Quick Start preview
UA-5200 Series
Brand: ICP DAS USA Pages: 4
ETC Response Analog IO Gateway Setup Manual preview
Response Analog IO Gateway
Brand: ETC Pages: 4
Berker 75710016 Quick Manual preview
75710016
Brand: Berker Pages: 4
T-VIPS CP560 User Manual preview
CP560
Brand: T-VIPS Pages: 200
Samson 5007-2 Series Mounting And Operating Instructions preview
5007-2 Series
Brand: Samson Pages: 72
ABB TG/S 3.1 Product Manual preview
TG/S 3.1
Brand: ABB Pages: 45
ABB RER601 Technical Manual preview
RER601
Brand: ABB Pages: 108
Motorola RG3000 User Manual preview
RG3000
Brand: Motorola Pages: 46
Motorola HH1620 Specifications preview
HH1620
Brand: Motorola Pages: 4
Motorola Netopia 7107-65 User Manual preview
Netopia 7107-65
Brand: Motorola Pages: 22
Motorola EASY START KIT HMEZ1000 - CELL PHONE SET UP Specifications preview
EASY START KIT HMEZ1000 - CELL PHONE SET UP
Brand: Motorola Pages: 2
Motorola Netopia 2200 Series Specification Sheet preview
Netopia 2200 Series
Brand: Motorola Pages: 5
Motorola Netopia 2247-62 Specification Sheet preview
Netopia 2247-62
Brand: Motorola Pages: 5
Motorola Netopia 3347-02 Datasheet preview
Netopia 3347-02
Brand: Motorola Pages: 3
Motorola Netopia 3347-02-ENT Datasheet preview
Netopia 3347-02-ENT
Brand: Motorola Pages: 3
Motorola Netopia 3387WG-VGx Datasheet preview
Netopia 3387WG-VGx
Brand: Motorola Pages: 3
Motorola Netopia 6150285-00-02 Important Safety Instructions preview
Netopia 6150285-00-02
Brand: Motorola Pages: 2

Brands by name

Popular brands

Load more brands