manualshive.com logo in svg

Cisco Linksys SPA9000, Administration Manual

The Cisco Linksys SPA9000 is an advanced communication system designed for small businesses. Ensure smooth operation with the Administration Manual, available for free download from manualshive.com. This comprehensive manual covers setup, troubleshooting, and customization, empowering users to harness the full potential of this powerful product.

Share
Download
background image

SPA9000 Field Reference

Router Tab

SPA9000 Voice System Administration Guide

196

B

 

Router tab > Wan Setup page > 

QOS Settings section

Router tab > Wan Setup page > 

VLAN Settings section

Router tab > 

Lan Setup page and Application page

NOTE

Linksys Engineering and Quality Assurance strongly advise against using the 
SPA9000 as a router. For this reason, the 

Lan Setup

 and 

Application

 tabs should not 

be modified from the default, unused state. The SPA9000 must only be connected 
to a switch via the SPA9000 INTERNET RJ45 connector. Do not connect any cable 
to the SPA9000 ETHERNET port, or you may experience degraded audio 
performance.

QoS Policy

The queueing discipline, set to none or token bucket filter 
(TBF). TBF limits the rate of transmission to not attempt to 
exceed the Maximum Uplink Speed.

QOS QDisc

Allow QoS Queuing. Options are None or TBF (token 
bucket filter). Information can be found at about TBF at: 

lartc.org/howto/lartc.qdisc.classless.html

Maximum Uplink Speed

Define this value to allow the token bucket filter queueing 
discipline to manage traffic flow to ensure high quality voice 
audio.

Enable VLAN

Enable voice data to be tagged with the defined VLAN ID.

NOTE

Choose 

yes

 If your SPA9000 is connected to a switch 

that uses VLAN tagging. 

VLAN ID

The VLAN tag for the VLAN to which the SPA9000 is 
assigned

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for Linksys SPA9000































































































































































































































































































Reviews:

No comments

Related manuals for Linksys SPA9000

ZIEHL-ABEGG DIG-2019NE Original Operating Instructions preview
DIG-2019NE
Brand: ZIEHL-ABEGG Pages: 23
Handlink Technologies WG-500P M User Manual preview
WG-500P M
Brand: Handlink Technologies Pages: 156
hilscher EU5C-SWD-ETHERCAT User Manual preview
EU5C-SWD-ETHERCAT
Brand: hilscher Pages: 98
Pathway connectivity solutions Pathport OCT User Manual preview
Pathport OCT
Brand: Pathway connectivity solutions Pages: 14
Pace 5111NV Installation Manual preview
5111NV
Brand: Pace Pages: 19
Banner SureCross Performance FlexPower DX80G9M2S-P7 Manual preview
SureCross Performance FlexPower DX80G9M2S-P7
Brand: Banner Pages: 10
Grandstream Networks GXE5024 User Manual preview
GXE5024
Brand: Grandstream Networks Pages: 10
ZyXEL Communications SBG3500-N Series Quick Start Manual preview
SBG3500-N Series
Brand: ZyXEL Communications Pages: 10
SharkRF openSPOT3 User Manual preview
openSPOT3
Brand: SharkRF Pages: 131
Ursalink UG65 Quick Start Manual preview
UG65
Brand: Ursalink Pages: 25
Logic IO RTCU MX2 turbo Technical Manual preview
RTCU MX2 turbo
Brand: Logic IO Pages: 36
ERT VIPER User Manual preview
VIPER
Brand: ERT Pages: 45
Cell2Tel C2T-XT2000 Quick Start Manual preview
C2T-XT2000
Brand: Cell2Tel Pages: 34
Comelit 1456 Technical Manual preview
1456
Brand: Comelit Pages: 28
VOPtel VG2020 User Manual preview
VG2020
Brand: VOPtel Pages: 38
Hitron CODA D3.1 Quick Start Manual preview
CODA D3.1
Brand: Hitron Pages: 2
ECKELMANN Combi Operating Instructions Manual preview
Combi
Brand: ECKELMANN Pages: 58
GRASS VALLEY UCP-3901 User Manual preview
UCP-3901
Brand: GRASS VALLEY Pages: 210

Brands by name

Popular brands

Load more brands