manualshive.com logo in svg

Cisco Linksys SPA9000, Administration Manual

The Cisco Linksys SPA9000 is an advanced communication system designed for small businesses. Ensure smooth operation with the Administration Manual, available for free download from manualshive.com. This comprehensive manual covers setup, troubleshooting, and customization, empowering users to harness the full potential of this powerful product.

Share
Download
background image

Administering the SPA400 and Voice Mail Service

Configuring a SPA400 for Voice Mail Service

SPA9000 Voice System Administration Guide

112

5

 

Configuring a SPA400 for Voice Mail Service

The SPA400 includes a USB adapter with an integrated voice mail application for 
the users and extensions that are configured on the SPA9000. The integrated 
voice mail application server supports 32 configurable voice mail accounts. 
Although a SPA9000 can be configured with up to four SPA400 devices, only one 
SPA400 can be configured with the voice mail server. 

NOTE

Important:

 For optimum voice mail performance, a SPA400 should be dedicated to 

the voice mail application when either of the following conditions is met:
1) More than 2 FXO connections are required
—OR—
2) More than 2 users commonly access voice mail at the same time.

This section includes the following topics:

•

“Voice Mail Capacity,” on page112

•

“Configuring Local Voice Mail Service on a SPA400,” on page113

•

“Setting Up Voice Mail on Each Station,” on page116

•

“Enabling Remote Voice Mail Access (Optional),” on page119

NOTE

Before you begin any of the procedures in this section, configure a SPA9000 line 
interface for this device. See 

“Configuring a Line Interface for a SPA400 (PSTN or 

Voice Mail),” on page 60

.

Voice Mail Capacity

The provided 128-Mb USB drive can store more than 3.8 hours of messages 
(approximately 230 60-second messages). For example, with 10 voice mail users, 
each user can store up to 23 60-second messages. When disk capacity is 
reached, inbound voice mail deposit attempts are disconnected. If additional voice 
mail storage is required, please contact Linksys for recommended high-capacity 
USB drives. 

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for Linksys SPA9000































































































































































































































































































Reviews:

No comments

Related manuals for Linksys SPA9000

Pathport 6822 Manual preview
6822
Brand: Pathport Pages: 2
rainforest EAGLE-200 User Manual preview
EAGLE-200
Brand: rainforest Pages: 20
F-SECURE MESSAGING SECURITY GATEWAY - Installation Manual preview
MESSAGING SECURITY GATEWAY -
Brand: F-SECURE Pages: 19
Moxa Technologies MGate MB3480 Quick Installation Manual preview
MGate MB3480
Brand: Moxa Technologies Pages: 6
NeoGate TE200 User Manual preview
TE200
Brand: NeoGate Pages: 41
Bticino BTI-N4510C-EN Installation Manual preview
BTI-N4510C-EN
Brand: Bticino Pages: 28
Night Owl WG4 Series Quick Setup Manual preview
WG4 Series
Brand: Night Owl Pages: 8
SystemAir RS485 User Manual preview
RS485
Brand: SystemAir Pages: 16
Argent Data Systems Tracker4 Manual preview
Tracker4
Brand: Argent Data Systems Pages: 34
Philips Dynalite DTK622-USB Installation Instructions preview
Dynalite DTK622-USB
Brand: Philips Pages: 2
Philips Dynalite DMNG232 Installation Instructions preview
Dynalite DMNG232
Brand: Philips Pages: 2
Philips Dynalite DDNI-LON Installation Instructions preview
Dynalite DDNI-LON
Brand: Philips Pages: 2
Philips Dynalite DDNG485 User Manual preview
Dynalite DDNG485
Brand: Philips Pages: 2
Philips Dynalite DDNG232 Installation Instructions preview
Dynalite DDNG232
Brand: Philips Pages: 2
Philips Dynalite DDNG100BT Installation Manual preview
Dynalite DDNG100BT
Brand: Philips Pages: 2
Philips Dynalite DDNG-KNX Installation Instructions preview
Dynalite DDNG-KNX
Brand: Philips Pages: 2
Philips Dynalite DDMIDC8 Installation Instructions preview
Dynalite DDMIDC8
Brand: Philips Pages: 2
Philips CPWBS054 Quick Start Manual preview
CPWBS054
Brand: Philips Pages: 80

Brands by name

Popular brands

Load more brands