Cisco Linksys SPA9000 Administration Manual Download

Page: 123 / 286

Administering the SPA400 and Voice Mail Service

Managing the Voice Mail Messages on the USB Key

SPA9000 Voice System Administration Guide

121

Managing the Voice Mail Messages on the USB Key

To delete unneeded voice mail messages on the USB key, refer to the procedure
below.

NOTE

When you click the Reset button, all the voice mail message for all users will be
deleted. The deleted voicemail messages are not recoverable.

STEP 1

Connect to the SPA400 administration web server. (See

“Connecting to the

SPA400 Administration Web Server,” on page103

STEP 2

Click

Administration tab > USB Setting

SPA400 Administration > USB Setting

STEP 3

Check the

I want to reset USB

check box.

STEP 4

Click

Reset

STEP 5

When the confirmation message appears, click

to continue or click

Cancel

end the operation without deleting the messages.

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for Linksys SPA9000































































































































































































































































































Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands

Cisco Linksys SPA9000, Administration Manual

Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands