Cisco Linksys SPA9000 Administration Manual Download

Page: 271 / 286

SPA400 Field Reference

Setup

SPA9000 Voice System Administration Guide

269

Setup tab>

Voicemail Users

Mailbox manage number

The phone number that the SPA9000 uses to access voice
mail

NOTE

This value appears in the

Proxy and Registration:

Mailbox Manage URL

field on the SPA9000 line interface

page.

Example

•

Mailbox manage number:

800

•

Mailbox Manage URL:

[email protected]:5090

Default:

800

AA Language

The language that is used by the voice mail Auto Attendant:
English, German, Spanish, French, Dutch, Portuguese, Czech

Default:

English

Maximum length of a
voicemail message

The maximum number of seconds that can elapse before a
voice mail message is ended automatically

Default:

User Setting

Enable User

Enables the mailbox

NOTE:

Each mailbox can be assigned to a client station

that is managed by the SPA9000. Before a station can
deposit and access voicemail, the mail box ID must be
configured through the

Ext N

page.

User ID

The mailbox ID

Password

The password for the mailbox

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for Linksys SPA9000































































































































































































































































































Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands

Cisco Linksys SPA9000, Administration Manual

Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands