Cisco Linksys SPA9000 Administration Manual Download

Page: 63 / 286

Configuring Phone Lines and Calling Routing Behavior

Configuring Line Interfaces on the SPA9000

SPA9000 Voice System Administration Guide

STEP 1

Start Internet Explorer, and then enter the IP address of the SPA9000. Click Admin
Login and then click Advanced.

STEP 2

Click

Voice tab > Line

, where

represents the line interface number.

STEP 3

From the

Line Enable

drop-down list, choose

yes

STEP 4

Enter the following information:

•

User ID:

Enter a user ID, such as 9000.

This entry must exactly match the user ID on the

SPA400

Setup > SPA9000

Interface

page,

User ID

field. For more information, see

“Configuring a SPA400

to Interoperate with the SPA9000,” on page108

•

Proxy:

Enter the IP address of the SPA400.

•

Register Expires:

This setting ensures that the SPA9000 and SPA400 are resynchronized every
60 seconds. This setting ensures that any changes in settings are synchronized
on both devices.

SPA9000 Voice > Line: Subscriber Information, Proxy and Registration

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for Linksys SPA9000































































































































































































































































































Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands

Cisco Linksys SPA9000, Administration Manual

Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands