Cisco Linksys SPA9000 Administration Manual Download

Page: 167 / 286

SPA9000 Voice System Administration Guide

165

Advanced Topics in SPA9000 Administration

This appendix provides more detailed technical information for administrators who
want to understand how the SPA9000 Voice System works.

•

“Technology Background,” on page165

•

“SPA9000 Architecture,” on page170

•

“SIP-NAT Interoperation,” on page172

•

“Advanced Call Control and Routing,” on page173

•

“Configuring Vertical (Supplementary) Service Codes,” on page173

•

“Advanced Topics for SPA400 Voice Mail Service,” on page178

•

“Remote Provisioning Features,” on page183

Technology Background

This section provides background information about the technology and protocols
used by the SPA9000 system. It includes the following topics:

•

“Session Initiation Protocol,” on page166

•

“SPA9000 Media Proxy,” on page167

•

“Using the SPA9000 with a Firewall or Router,” on page168

•

“SPA400 SIP-PSTN Gateway,” on page169

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for Linksys SPA9000































































































































































































































































































Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands

Cisco Linksys SPA9000, Administration Manual

Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands