Cisco Linksys SPA9000 Administration Manual Download

Page: 83 / 286

Configuring Phone Lines and Calling Routing Behavior

Managing the Line Selection for Outbound Calls

SPA9000 Voice System Administration Guide

•

Wildcard characters

EXAMPLE:

(<:L1>51*,577?)

In this example, Line 1 can be used when either of the following number
patterns is dialed:

•

The user dials a number that starts with 51, followed by any other
characters.

•

The user dials any four-digit number starting with 577.

Entering a Call Routing Rule

Use the following procedure to enter a call routing rule.

STEP 1

Start Internet Explorer, and then enter the IP address of the SPA9000. Click Admin
Login and then click Advanced.

STEP 2

Click

Voice tab > SIP

STEP 3

Scroll down to the

PBX Parameters

section.

STEP 4

In the

Call Routing Rule

field, enter the rule that you want to apply

STEP 5

Click

Submit All Changes

STEP 6

To verify your progress, place a call to a phone that has caller ID, and confirm that
the expected number appears.

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for Linksys SPA9000































































































































































































































































































Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands

Cisco Linksys SPA9000, Administration Manual

Search results

Summary of Contents for Linksys SPA9000

Reviews:

Related manuals for Linksys SPA9000

Brands by name

Popular brands