manualshive.com logo in svg

Cisco Linksys SPA9000, Administration Manual

The Cisco Linksys SPA9000 is an advanced communication system designed for small businesses. Ensure smooth operation with the Administration Manual, available for free download from manualshive.com. This comprehensive manual covers setup, troubleshooting, and customization, empowering users to harness the full potential of this powerful product.

Share
Download
background image

Administering the SPA400 and Voice Mail Service

Configuring a SPA400 for Voice Mail Service

SPA9000 Voice System Administration Guide

115

5

 

NOTE

Later you configure each client station for voice mail access to the 
mail boxes that you create on this page.

STEP 6

Click Save Settings at the bottom of the page.

STEP 7

Restart the SPA400 by completing the following steps: 

a. Click

 Administration

 

tab > 

Reboot.

b. Click the Restart System button. 

c. When the confirmation message appears, click OK. The SPA400 reboots. 

d. When the 

Reboot OK

. Go to Setup page?

 message appears, click OK.

STEP 8

To verify your progress, click the Status tab, and verify the following settings:

•

USB status: 

Mount

•

Voice mail status:

 OK

•

SPA9000 Registration status:

 Registered 

SPA400 Status

NOTE

If the SPA registration status is not Registered, trying powering off the 
SPA9000 and powering it on again.

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for Linksys SPA9000































































































































































































































































































Reviews:

No comments

Related manuals for Linksys SPA9000

Safeline GL1 Quick Manual preview
GL1
Brand: Safeline Pages: 76
Pathway connectivity solutions Pathport OCTO 64 Series User Manual preview
Pathport OCTO 64 Series
Brand: Pathway connectivity solutions Pages: 70
ZyXEL Communications P-661HNU-FX Quick Start Manual preview
P-661HNU-FX
Brand: ZyXEL Communications Pages: 18
ioSelect WMR-900 Operating Manual preview
WMR-900
Brand: ioSelect Pages: 160
MSA HUB Operating Manual preview
HUB
Brand: MSA Pages: 34
hilscher NIOT-E-TIB100-GB-RE User Manual preview
NIOT-E-TIB100-GB-RE
Brand: hilscher Pages: 263
Aruba EC-10104 Installation Manual preview
EC-10104
Brand: Aruba Pages: 20
ActionTec T3260 User Manual preview
T3260
Brand: ActionTec Pages: 83
Teltonika TRB141 Quick Start Manual preview
TRB141
Brand: Teltonika Pages: 6
3Com OfficeConnect 3CR856-95-US Release Notes preview
OfficeConnect 3CR856-95-US
Brand: 3Com Pages: 2
3Com 3CRWE51196 - OfficeConnect Wireless Cable/DSL Gateway Installation Manual preview
3CRWE51196 - OfficeConnect Wireless Cable/DSL Gateway
Brand: 3Com Pages: 2
Asyril Asycube CC-Link Gateway User Manual preview
Asycube CC-Link Gateway
Brand: Asyril Pages: 21
EuroTech Communication VOIP ALL SERIES User Manual preview
VOIP ALL SERIES
Brand: EuroTech Communication Pages: 77
AWB WiMAX RG231 User Manual preview
WiMAX RG231
Brand: AWB Pages: 59
RTA 460ECBMS Product User Manual preview
460ECBMS
Brand: RTA Pages: 71
3Com OfficeConnect 3C100XF Quick Start Manual preview
OfficeConnect 3C100XF
Brand: 3Com Pages: 12
XAVI Technologies Corp. X7968r User Manual preview
X7968r
Brand: XAVI Technologies Corp. Pages: 108
HELVAR DIGIDIM EnOcean 434 Installation Manual preview
DIGIDIM EnOcean 434
Brand: HELVAR Pages: 4

Brands by name

Popular brands

Load more brands