Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 88 | Manualshive

Page: 88 / 617

Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 88

NOTE:

To remove the head restraint, raise it as far as it can

go. Then, push the release button and the adjustment
button at the base of each post while pulling the head
restraint up. Seatback angle may need to be adjusted to
fully remove the head restraint. To reinstall the head
restraint, put the head restraint posts into the holes and
push downward. Then, adjust the head restraint to the
appropriate height.

WARNING!

•

A loose head restraint thrown forward in a collision
or hard stop could cause serious injury or death to
occupants of the vehicle. Always securely stow re-
moved head restraints in a location outside the
occupant compartment.

•

ALL the head restraints MUST be reinstalled in the
vehicle to properly protect the occupants. Follow the
re-installation instructions above prior to operating
the vehicle or occupying a seat.

Head Restraints — Second Row

The second row outboard head restraints are adjustable. To
raise the head restraint, pull upward on the head restraint.
To lower the head restraint, push the adjustment button,
located at the base of the head restraint, and push down-
ward on the head restraint.

Full Forward Position

86

GETTING TO KNOW YOUR VEHICLE

«
...
86
87
88
89
90
...
»

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments