manualshive.com logo in svg

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 414 / 617

Share
Download
Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 414

CAUTION!

Do not attempt to raise the vehicle by jacking on
locations other than those indicated in the Jacking
Instructions for this vehicle.

1. Loosen (but do not remove) the wheel lug nuts by

turning them to the left one turn while the wheel is still
on the ground.

2. There are two jack engagement locations on each side of

the vehicle body indicated by the triangular lift point
symbol on the sill molding.

Do not raise the vehicle

until you are sure the jack is fully engaged.

Jack Warning Label

Jack Locations

412

IN CASE OF EMERGENCY

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments