Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 124

Page: 124 / 617

WINDOWS

Power Windows

You can control either the front or rear windows using
controls located on the driver’s door trim panel.

The driver may lock out the rear power windows by
pushing the bar control just below the power window
controls.

The controls will operate only when the ignition switch is
in the ON/RUN or ACC position and during power
accessory delay.

Driver’s Power Window Controls

1 — Front Driver And Passenger Window Controls
2 — Rear Passenger Window Controls
3 — Power Window Lockout Switch — If Equipped

122

GETTING TO KNOW YOUR VEHICLE

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Pacifica Hybrid 2018

Reviews:

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 124 / 617

Search results

Summary of Contents for Pacifica Hybrid 2018

Reviews: