Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 86 | Manualshive

Page: 86 / 617

Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 86

HEAD RESTRAINTS

Head restraints are designed to reduce the risk of injury by
restricting head movement in the event of a rear impact.
Head restraints should be adjusted so that the top of the
head restraint is located above the top of your ear.

WARNING!

•

All occupants, including the driver, should not oper-
ate a vehicle or sit in a vehicle’s seat until the head
restraints are placed in their proper positions in
order to minimize the risk of neck injury in the event
of a crash.

•

Head restraints should never be adjusted while the
vehicle is in motion. Driving a vehicle with the head
restraints improperly adjusted or removed could
cause serious injury or death in the event of a
collision.

Head Restraints — Front Seats

The front driver and passenger seats are equipped with
four-way head restraints.

To raise the head restraint, pull upward on the head
restraint. To lower the head restraint, push the adjustment
button, located at the base of the head restraint, and push
downward on the head restraint. Front head restraints are
also adjustable forward and rearward. To adjust the head
restraint forward, pull forward on the top of the head
restraint to desired position. To adjust the head restraint

Front Head Restraint

1 — Release Button
2 — Adjustment Button

84

GETTING TO KNOW YOUR VEHICLE

«
...
84
85
86
87
88
...
»

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments