manualshive.com logo in svg

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 427 / 617

Share
Download
Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 427

Drive Vehicle:

Immediately after injecting sealant and
inflating the tire, drive the vehicle 5
miles (8 km) or 10 minutes to ensure
distribution of the Tire Service Kit Seal-
ant within the tire. Do not exceed
50 mph (80 km/h).

WARNING!

Tire Service Kit is not a permanent flat tire repair. Have
the tire inspected and repaired or replaced after using
Tire Service Kit. Do not exceed 50 mph (80 km/h) until
the tire is repaired or replaced. Failure to follow this
warning can result in injuries that are serious or fatal
to you, your passengers, and others around you. Have
the tire checked as soon as possible at your authorized
dealer.

After Driving:

Pull over to a safe location. Refer to “Whenever You Stop
To Use Tire Service Kit” in this section before continuing.

1. Uncoil the Sealant Hose, and then remove the cap from

the fitting at the end of the hose.

2. Place the Tire Service Kit flat on the ground next to the

deflated tire.

3. Remove the cap from the valve stem, and then screw

the fitting at the end of the Sealant
Hose onto the valve stem.

4. Uncoil the power plug and insert the plug into the

vehicle’s 12 Volt power outlet.

7

IN CASE OF EMERGENCY

425

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments