manualshive.com logo in svg

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 463 / 617

Share
Download
Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 463

3. To remove the wiper blade from the wiper arm, grasp

the bottom end of the wiper blade nearest to wiper arm
with your right hand. With your left hand hold the
wiper arm as you pull the wiper blade away from the
wiper arm past its stop far enough to unsnap the wiper
blade pivot pin from the receptacle on the end of the
wiper arm.

NOTE:

Resistance will be accompanied by an audible

snap.

4. Still grasping the bottom end of the wiper blade, move

the wiper blade upward and away from the wiper arm
to disengage.

5. Gently lower the tip of the wiper arm onto the glass.

Wiper Blade In Folded Out Position

1 — Wiper Arm Pivot Cap
2 — Wiper Arm
3 — Wiper Blade

Wiper Blade Removed From Wiper Arm

1 — Wiper Blade
2 — Wiper Blade Pivot Pin
3 — Wiper Arm
4 — Wiper Arm Receptacle

8

SERVICING AND MAINTENANCE

461

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments